ImageGear Supported Versions

• Version 1.01 - 1991
• Version 1.02 - Added ability for thumbnails to be color-mapped and JPEG compressed.

ImageGear Supported Features

• IGFilterFormatFlags.DETECTSUPPORT - autodetection
• IGFilterFormatFlags.PAGEREADSUPPORT - single page file reading
• IGFilterFormatFlags.PAGEINSERTSUPPORT - single-page file writing

ImageGear Read Support ("Native" Filter)

• ImGearCompressions.JPEG (Lossy):
  • Grayscale: 8, 12 bpp;
  • RGB: 24 bpp;
  • CMYK: 32 bpp;
  • RGB + Alpha: 32 bpp
• ImGearCompressions.JPEG (Lossless):
  • Grayscale: 8, 16 bpp;
  • RGB: 24, 48 bpp;
  • CMYK: 32 bpp;
  • RGB + Alpha: 32 bpp
• ImGearCompressions.JPEG (Progressive JPEG):
  • Grayscale: 8, 12 bpp;
  • RGB: 24 bpp;
  • RGB + Alpha: 32 bpp

ImageGear Write Support ("Native" Filter)

• ImGearCompressions.JPEG (Lossy):
  • Grayscale: 8, 12 bpp;
  • RGB: 24 bpp;
  • RGB + Alpha: 32 bpp
  • CMYK: 32 bpp
• ImGearCompressions.JPEG (Lossless):
  • Grayscale: 8, 16 bpp;
  • RGB: 24 bpp
• ImGearCompressions.JPEG (Progressive):
  • Grayscale: 8, 12, 16 bpp;
  • RGB: 24 bpp

ImageGear Read Support ("Managed" Filter)

• ImGearCompressions.JPEG (Lossy):
  • Grayscale: 8, 12 bpp;
  • RGB: 24, 36 bpp;
  • CMYK: 32 bpp;
  • RGB + Alpha: 32 bpp
• ImGearCompressions.JPEG (Lossless):
  • Grayscale: 8, 16 bpp;
  • RGB: 24, 48 bpp;
  • CMYK: 32 bpp;
  • RGB + Alpha: 32 bpp
• ImGearCompressions.JPEG (Progressive JPEG):
  • Grayscale: 8, 12 bpp;
  • RGB: 24 bpp;
  • CMYK: 32 bpp;
  • RGB + Alpha: 32 bpp

ImageGear Write Support ("Managed" Filter)

• ImGearCompressions.JPEG (Lossy):
  • Grayscale: 8, 12 bpp;
  • RGB: 24, 36 bpp;
  • RGB + Alpha: 32 bpp (RGBA saving is disabled by default. Set AllowRGBASaving control parameter to true to enable it.)
  • CMYK: 32 bpp2 (CMYK saving is enabled by default. You can disable it by setting AllowCMYKSaving control parameter to false.)
• ImGearCompressions.JPEG (Lossless):
  • Grayscale: 8, 16 bpp;
  • RGB: 24 bpp

ImageGear Filter Control Parameters

ImageGear .NET provides two versions of JPEG filters. One is 100% "managed", and the other relies on native codecs and is optimized for the best compression and decompression performance. "Managed" filter is created by default when initializing IG common formats. Use CreateJpegFormat method to switch to optimized filter. Each filter has its own set of control parameters listed below:

ImageGear "Native" Filter Control Parameters

ImageGear "Managed" Filter Control Parameters

SaveExistingEXIFMetadata works in combination with SaveEXIFMetadata parameter, as shown in the table below:

Comments

JPEG is normally associated with the JPEG compression scheme, but it is also implemented into the JFIF file format. This format was developed to store JPEG-encoded data, and to exchange it between applications or operating systems that are normally incompatible.

The header of the JFIF contains the version number, the image dots per inch (DPI), or dots per centimeter, and an optional thumbnail (miniature) RGB representation of the main image. Version 1.02 handles thumbnails differently by storing them separately, rather than in the identification marker of the header.

The raw JPEG data is surrounded by two markers, an "SOI" (start of image) marker, and an "EOI" (end of image) marker. See Lossy JPEG Compression for more about JPEG compression.

JFIF is considered a non-proprietary file format. Many proprietary file formats contain JPEG data, incorporating their own application-specific data structures. Another non-proprietary format that uses JPEG-encoded data is TIFF file format, version 6.0.

Loading and Saving JPEG-Compressed Images

ImageGear supports the reading and writing of three types of JPEG compression: baseline JPEG (Lossy), Progressive JPEG, and Lossless JPEG. When you load a JPEG-compressed file, ImageGear detects the type of JPEG compression and decompresses the image automatically. However, if you want to save an image with a JPEG compression scheme other than baseline JPEG, you must use "SaveType" parameter (for "Managed" filter) or "JpegSaveType" parameter (for "Native" filter) to specify the type of JPEG compression.

JPEG Thumbnails

The JPEG format can store thumbnails, which are small representations of the original image. These images are stored in uncompressed form and can significantly decrease your overall compression ratio. (Uncompressed thumbnails sometimes occupy more space than the original JPEG image when compressed). Use this option carefully.

Lossless JPEG Predictor Settings

The Lossless JPEG scheme is "predictive" in nature; it uses the values of surrounding pixels in addition to the value of the original pixel to calculate a predictor value, which it then subtracts from the value of the original pixel. The resulting pixel value will be reduced such that it can be compressed more than the original value. The higher the number of neighboring pixels used, the higher the compression will be.

Regardless of the predictor value setting, the quality of the image will remain the same. The difference is that if you choose to optimize for space by setting a high predictor value, you will have to give up some speed, as the decompression will take longer to perform.

ImageGear lets you set the predictor value using "Predictor" control parameter. The ImageGear default for this setting is 1. The allowed range is 1-7. Values outside of the allowed range of 1-7 will be mapped to a value of 5. The graphic below shows a predictor (x) and three reconstructed samples (a,b,c) immediately to the left, immediately above, and diagonally to the left of the current sample

Lossless JPEG does not apply DCT for an image as per the Lossy JPEG compression. Instead, it uses a DPCM difference coding, which can be carried out with any one of seven different prediction modes. Correspondingly, the "Predictor" control parameter can be set to a value between 1 and 7. In the table below, you will see what algorithm your setting of 1-7 will use, where Px is the predictor, and Ra, Rb, and Rc are the reconstructed samples:

JPEG Quality

The baseline JPEG specification calls for a quality setting. The lower the setting, the greater the number of original pixels lost, and therefore the smaller the resulting compressed file will be. ImageGear lets you set the quality of compression with values of type INT between 1-100, where 100 provides the highest retention of original pixel values. A setting of 100 does not mean that the image includes 100% of all original pixel values. With Lossy JPEG, there is no such thing as "no loss". Control parameter for setting Lossy JPEG quality is "Quality" (for "Managed" filter). Please see description of "Chrominance" and "Luminance" control parameters to apply JPEG quality settings for the "Native" filter.

References Used

Brown, C. Wayne, and Barry J. Shepherd. Graphics File Formats: Reference and Guide. Greenwich, CT.: Manning Publications, 1992.

Kay, David C. and John R. Levine. Graphics File Formats. Windcrest Books, 1992.

Murray, James D. and William vanRyper. Encyclopedia of Graphics File Formats. Sebastopol, CA: O'Reilly & Associates, Inc., 1994.