Supported PHP Versions

The PrizmDoc PHP Sample requires PHP version 5.4 and above. 

Linux Installation

1. Install PrizmDoc for Linux and verify the service is working correctly. The installation will place the PHP samples in the following directory: /usr/share/prizm/Samples/php.
2. Install Apache and PHP. Refer to the directions that are specific to your distribution.
3. Add the following to the Apache configuration:

Example	Copy Code
Alias /pccis_sample /usr/share/prizm/Samples/php <Directory /usr/share/prizm/Samples/php> AllowOverride All Require all granted </Directory>

4. On the command line, first check that the configuration file validates:

The command you use depends on the version of Apache you are using.

Example	Copy Code
apache2ctl configtest

5. Then restart the Apache service to read the configuration changes:

Example	Copy Code
apache2ctl restart

6. Give read/write permissions to the "Documents" folder, the "markup" folder and the "markupLayerRecords" folder. Give read permissions to the ImageStamp folder. These folders are installed to: /usr/share/prizm/Samples on Linux. For more information, see the "Configuration with pcc.config" section below.
7. Test the sample application in a browser. The following will route you directly to the Viewer sample splash page: http://myservername:port/pccis_sample/splash

Install Considerations

Ubuntu

For Ubuntu users: In Ubuntu 13 and up, the php_curl module was unbundled from the default PHP install. This module is required by the PHP sample, and should be installed separately, as such:

sudo apt-get install php5-curl

Apache

Depending on how you install PHP for Apache, you may need to install the Apache PHP addition, as such:

sudo apt-get install libapache2-mod-php5

Configure PHP Web Tier with SELinux

When running PHP Web Tier on Security-Enhanced Linux you may experience issues with loading documents in the Viewer, and may see the following errors in Apache's log files: PHP Warning: file_get_contents(<URL>): failed to open stream: Permission denied

The reason for the error is because the Web Tier needs to contact the PrizmDoc Server. By default SELinux disallows Apache processes from connecting out. You can run the following command to allow the web tier to function:

setsebool -P httpd_can_network_connect 1

Similarly, when attempting to upload a document, the PHP application may appear unresponsive. When reviewing the document upload response in your browser’s console, you may see a 403 Forbidden error. Security-Enhanced Linux prevents the PHP / Apache HTTP application from writing to the file system by default. You can run the following command to set the httpd_sys_rw_content_t policy for the Samples directory:  

chcon -R -t httpd_sys_rw_content_t /usr/share/prizm/Samples/

Windows Installation

By default, the PHP sample is installed to: C:\Prizm\Samples\php, assuming use of the default PrizmDoc location of C:\Prizm.

IIS

Install IIS, along with the CGI component, and then install and configure PHP. The instructions and installer provided on the IIS site are now old and outdated, as they install PHP version 5.3. Instead, install the latest version of PHP using the Web Platform Installer. If using an already configured server, make sure you are using PHP version 5.4 or higher.

To configure the sample:

1. Note the location of the PHP sample as described above. If you changed the PrizmDoc default install location, note the comparable sample in the install location you specified.
2. Open the IIS Manager.
3. In the Sites list, select the site you want to add the PHP sample to, such as "Default Web Site". Right-click on it and select "Add Virtual Directory…".
4. In the Alias field, type the URL path you want to use for the sample. We will use "pccis_sample" as an example here.
5. In the Physical Path field, use the location we noted above. Click OK to create the virtual directory.

Now you can browse to http://localhost/pccis_sample/splash in your browser to see the PHP sample.

Apache

Install Apache, or an Apache stack like XAMPP or WAMP server, and a supported version of PHP.

To configure the sample:

1. Note the location of the PHP sample as described above. If you changed the PrizmDoc default install location, note the comparable sample in the install location you specified.
2. Open the httpd.conf file of your Apache install.
3. In the block starting with "<IfModule alias_module>", add the following to the end of the block:

Example	Copy Code
# PCC PHP sample alias Alias /pccis_sample "C:/Prizm/Samples/php" <Directory "C:/Prizm/Samples/php"> Allow from all Require all granted </Directory>

4. Restart Apache so that it picks up the new settings.

Now you can browse to http://localhost/pccis_sample/splash in your browser to see the PHP sample.

Optional Configuration

By default, PHP has a small file size upload. If you need to be able to upload larger files through the splash page, you may need to change the following values in the php.ini file of your PHP installation:

upload_max_filesize = 1000M
post_max_size = 1000M

This sets the file upload to 1GB, which should be enough to test most files through the splash page. These settings may be too high for a production service, so adjust those accordingly when deploying to production.

Configure PHP Web Tier with SELinux

When running PHP Web Tier on Security-Enhanced Linux you may experience issues with loading documents in the Viewer, and may see the following errors in Apache's log files: PHP Warning: file_get_contents(<URL>): failed to open stream: Permission denied

The reason for this is that the Web Tier needs to contact the PrizmDoc Server. By default SELinux disallows Apache processes from connecting out. You can run the following command to allow the web tier to function:

setsebool -P httpd_can_network_connect 1

Browsing the Sample

From the splash page you have three options:

1. Choice of Viewer:  you can choose to load either the Full Viewer, the Book Reader, or the Comparison Viewer.

2. Select a sample document - OR - upload a document: 

You can choose any of the 5 sample documents (Word, PDF, CAD, Tiff or JPEG). Or, you can upload a document from an arbitrary location on your computer. Note that dragging and dropping a file on this page is not supported in Internet Explorer 8.

3. Full Viewer:

If you select Full Viewer on the splash page, then documents will be viewed with the full-featured, out-of-the-box responsive Viewer:

4. Book Reader:

If you select Book Reader on the splash page, then documents will be viewed with the book reader. The book reader demonstrates how the Viewer can be heavily customized:

5. Comparison Viewer

This feature requires a Microsoft Office enabled PrizmDoc License.

If you select Comparison Viewer on the splash page, then you can upload two Word (.doc or .docx) files to be compared in the Viewer. The Comparison Viewer shows how two Word documents can be reviewed and compared using PrizmDoc:

 

Directory Structure

This folder contains 6 sub-folders, one folder for each of the four samples (full Viewer, book reader, e-signer and e-signer template designer) and two folders for the splash pages (main splash page and the e-sign splash page):

Each of the sample folders are completely self-contained, meaning that they contain all of the files needed to run the sample. Furthermore, with the exception of a few project files and build files, the sample folders contain only the files needed to run the sample.

Folder contents: full-viewer-sample

Folder contents: book-reader-sample

Folder contents: e-signer-sample

Folder contents: template-designer-sample

Configuration with pcc.config

The file pcc.config is used to configure the connection settings between the web tier and PrizmDoc Application Services. The file can be found at: <sample-folder-name>/viewer-webtier/pcc.config. This file is self-documenting, but a little information about the configuration options is given below.